您现在的位置: 首页 > 个人微信号 > 互联网 > 北京工地高坠事故|【高坠事故】突发!北京一工人在拆除脚手架时不慎坠亡!痛心:马上过年了,请注意安全!

微信扫一扫,添加关注

北京工地高坠事故|【高坠事故】突发!北京一工人在拆除脚手架时不慎坠亡!痛心:马上过年了,请注意安全!

【高坠事故】突发!北京一工人在拆除脚手架时不慎坠亡!痛心:马上过年了,请注意安全!点击上方“平安市政”可以订阅哦!北京市应急管理局官网消息:2020年1月14日16时许,在海淀区画眉山东路东侧翠湖科技园施工现场,北京佳苑佳宜建筑工程有限公司

微信号: 720weixin

联系QQ: 720weixin

57

热度

其他信息

北京工地高坠事故|【高坠事故】突发!北京一工人在拆除脚手架时不慎坠亡!痛心:马上过年了,请注意安全!
  • 0个评论

  • img

  • 720次点赞

  • 0个收藏

北京工地高坠事故|【高坠事故】突发!北京一工人在拆除脚手架时不慎坠亡!痛心:马上过年了,请注意安全!的详细说明:

【高坠事故】突发!北京一工人在拆除脚手架时不慎坠亡!痛心:马上过年了,请注意安全!


点击上方平安市政 可以订阅哦!


北京市应急管理局官网消息:2020年1月14日16时许,在海淀区画眉山东路东侧翠湖科技园施工现场,北京佳苑佳宜建筑工程有限公司一工人在拆除脚手架过程中不慎从高处坠落,后经医院抢救无效死亡。


脚手架拆除请记住:自上而下,先搭后拆,后搭先拆

一、脚手架拆除准备工作

1、根据检查架体结构及现场情况,编制拆除方案并经有关部门批准。 

2、脚手架拆除前,先划定安全范围,设置警戒线,项目负责人召集有关人员及作业人员对脚手架实地进行全面检查,重点检查扣件连接固定、支撑体系等是否符合安全要求,作业人员熟悉现场脚手架的搭设情况。 

3、确认建筑物及楼层材料已转运,确认不需要脚手架时,方可进行拆除。 

4、拆除前,应认真检查及时清除各层架体上留存的落地灰、砼块等存留材料或杂物,不能留下任何存在安全隐患的材料及杂物。

5、架体卸荷钢丝绳、脚手架刚性连墙杆、悬挑杆件拆除时,未经项目部施工员、质安员同意,现场任何操作人员不得随便拆除,以免影响脚手架的质量和安全。 

6、脚手架拆除时,现场作业人员必须做好防护措施,系好安全带,经过项目部施工员检查同意后才允许拆除,且由安全员现场跟踪监督。 

⑸7、脚手架拆除时,根据拆除现场的情况,现场外设置的警戒带,必须有专人看守,禁止与本次拆除无关人员进入。 

8、组织拆除人员做好安全技术交底,并有交底接受人签字,对作业人员交接清楚工作中要注意的相关安全技术要求。并准备好安全带、绳、吊具、工具,配备运输人员。 

9、拆除人员必须是专职架子工,持有特殊工种操作证方可参加作业。 

10、具体的安全交底由项目部安全部进行专门的安全交底。


二、外架拆除施工步骤与施工要点

按“自上而下,先搭后拆,后搭的先拆、逐步拆除”的原则拆除脚手架,严禁上下同时作业,不得采用踏步式或采取分段、分立面拆除。所有连墙杆应随脚手架逐层拆除,严禁先将连墙杆整层或数层拆除后再拆除架体;拆除连墙杆的同时应设临时连墙杆加固。 

1、脚手架拆除的施工工艺

脚手架拆除一般顺序为:

安全密目网→挡脚板→竹笆板→剪刀撑(只可在拆除层上拆除)→斜撑(只可在拆除层上拆除) →抛撑(只可在拆除层上拆除)→小横杆→大横杆→立杆→连墙杆。

б其中每段悬挑脚手架的悬挑槽钢及卸荷钢丝绳待其上脚手架全部拆完,才开始拆除。 

2、杆件拆除时注意事项 

工人作业前必须对个人防护用品进行检查合格后,方可投入使用。检查使用的工具是否牢固,防止掉落伤人。高空或悬空作业必须戴好安全帽和系好安全带。 

① 立杆—先抱住立杆再松开对接扣件,立刻稳定的将立杆拔出,平放下一步架管上,随即取出扣件,不能留在下一根立杆上。绝不允许扣件松开后立杆处于独立自由状态,没有及时拆除;拆除人员不可单独作业,应两人或多人合作拆除,保证拆除安全。 

② 大横杆、剪刀撑、斜撑—先拆中间对接扣件,托住中间再解开端头扣;剪刀撑、斜撑只能在拆除层上拆除,不得一次全部拆除,拆除剪刀撑时必须系好安全带,且两人以上合作拆除。

③ 抛撑—先用临时支撑加固后,才允许拆除抛撑。 

④ 所有连墙杆、卸荷钢丝绳随脚手架逐层拆除,严禁先将连墙杆整层或数层拆除后再拆脚手架。分段拆除高低差不大于2步,如高差大于2步时增设临时连墙杆加固。 

⑤ 当脚手架拆至下部最后一根长钢管约6.0m高度、时,应先在适当位置搭临时抛撑或拉结加固,后拆连墙杆。 

⑥ 拆除的钢管应自上而下传递,放置在下层未拆除的脚手板上、但堆置数量、高度、形式等按安全标准,用塔吊或施工梯运至地面,不得高空抛掷,以确保安全,并注意保护内外墙装饰面及幕墙,做好成品保护。

⑦ 松开后的扣件应及时拆除,放置在室内,不得高空抛掷,打包使用塔吊或者随施工梯运至地面。 

⑧ 拆除至安全平挡板时,应在适当的位置临时加固,方可拆除斜撑。 

⑨在拆架过程中,不得中途换人,如必须换人时,应将拆除情况交代清楚后方可离开。作业人员在离场前必须对自己或相邻人员拆除的脚手架进行检查,对松动的架子必须进行善后处理方可离开。 

⑩周围必须设围栏或竖立警戒标志,拆除脚手架过程中要有专人统一指挥,上下呼应,动作协调,当解开与另一个有关的结扣时,应先通知对方,以防坠落。

⑪材料工具塔吊运送,拆下的材料严禁抛掷。必须对所吊运的材料或构件进行捆绑牢固好后方可进行吊运。吊运时不得伤及他人或破坏建筑物、公共财物。运至地面的材料应按指定地点,随拆随运,分类堆放,当天拆当天清,拆下的扣件等要集中回收处理。 

3、外架拆除安全措施 

①外架拆除上岗人员必须持有特种待业上岗证。拆除脚手架必须认真向操作人员进行安全技术交底。班组长必须将脚手架拆除的相关安全技术要求对作业人员交接清楚。

②操作人员操作时必须正确佩戴安全帽,绑好安全带,穿防滑鞋,并配带工具袋,工具使用后装入袋中,不能放在架子上,以免落下伤人。 

③严禁酒后拆除作业,脚手架拆除人员必须身体健康,不能让有高血压,恐高症等病史的人员上架。

④拆除外架应在白天进行,并做好区域维护工作,在通道明显的地方挂好警示牌并由专人监督。在整个拆除作业过程中,项目安全员应切实作好现场巡查工作,在主要通道处设置警戒区,安排警戒员一名巡视,确保拆除作业顺利进行。 

⑤拆除外架首先拆除所有竹笆板及安全网,然后自上而下拆除,拆除时,先拆横杆,然后再拆除立杆,不能上下同时作业。连墙件必须与脚手架同步拆除。一般不允许分段、分立面拆除,如因施工需要必须分立面拆除时,应在暂不拆除的两端加设边墙点和横向水平支撑。拆下的扣件和配件应及时运至地面,严禁高空抛掷。 

⑥凡已松动的钢管、扣件应及时拆除运走。

⑦拆除下的钢管严禁向楼下抛投,应逐层向下传递。 

⑧拆除时应四周同时进行,禁止单面拆除后再拆另一面。 ɜː

⑨工人在架上作业时,应注意自我安全保护和他人的安全,避免发生碰撞、闪失和落物;严禁在♡架上嬉闹和坐在栏杆上等不安全处休息。 

⑩在作业中,禁止随意拆除脚手架的基本构架杆件、整体性杆件、连接紧固件和连墙件;确因需要拆除时,必须经技术总工同意,采取相应补救措施。 

r⑪拆除下的所有周转材料应分类堆放整齐。在进库存放以前逐件检查,有变形和损伤的部件应剔出修理,漆皮脱落者应重新由漆。 

北京工地高坠事故⑫如遇大风、大雨等恶劣天气,应立即停止作业,并注意保护脚手架,必要时加强与墙体的连接,确保牢靠。 

⑬外架拆除过程中,项目部各区工长和专职安全员在现场全过程巡查和监控,确保外架拆除限定区域内无其他人员作业。


三、架子工安全技术操作规程(拆除部分

1、拆除脚手架必须根据专项施工方案施工,操作人员必须经专业训练,考核合格后发给操作证,持证上岗操作。 

2、拆除脚手架必须正确使用安全带。拆除脚手架时,必须有专人看管,周围应设围栏或警戒标志,非工作人员不得人内。拆除连墙点前应先进行检查,采取加固措施后,按顺序由上而下,一步一清,不准上下同时交叉作业。   

3、拆除脚手架大横杆、剪刀撑,应先拆中间扣,再拆两头扣,由中间操作人往下顺杆子。 

4、拆下的脚手杆、脚手板、钢管、扣件、钢丝绳等材料,严禁往下抛掷。  

5、拆除的外脚手架组件必须分类、码堆、堆放整齐,不得杂乱无章。若不能及时运走,还要预留出足够的空地予以堆放。

以下动图送给高处作业不愿系安全带的员工

高空作业坠落身亡


脚手架不稳,白送性命


工地坍塌


幸好是个身手敏捷的小伙汁



毫无安全意识


一把没抓稳


Σ智商如此捉急



大树的报复


最后一张,安全措施做到位,即便点再被,死神没机会!


下面是一些好的做法

①高处临边作业法宝


求表扬?下面看看施工现场脚手架搭设时安全带挂设做法


就是作秀?那下面图片如果没带安全带呢?

登高作业十不准

1

患有登高禁忌者,如患有高血压、心脏病、贫血、癫痫等的工人不登高。

2

♈未按规定办理高处作业审批手续的不登高。

3

没有戴安全帽、系安全带,不扎紧裤管和无人监护不登高。

4

暴雨、大雾、六级以上大风时,露天不登高。

5

脚手架、跳板不牢不登高。

Ю6

梯子撑脚无防滑措施不登高。

7

穿着易滑鞋和携带笨重物件不登高。

8

石棉瓦和玻璃钢瓦上,无牢固跳板不登高。

Ò9

高压线旁无遮拦不登高。

10

夜间照明不足不登高。

作业人员从事登高作业,必须在三个方面加强安全管理:建立登高审批制度,建立登高用具管理制度,建立登高作业人员安全操作制度。





ə

防坠落安全管理通用制度





1、所有高空作业人员要接受高空作业安全知识教育;特种高空作业人员应持证上岗,上岗前应根据有关规定进行专门的安全技术培训,并在作业前实行安全技术交底签字手续。


2、高空作业人员应经过体检,合格才可上岗。项目部应作业人员提供合格的安全帽、安全带、安全网等安全劳动保护用品及相关安全防护用具。

3、参加施工的工人(包括学徒工、实习生、代培人员和民工)要熟悉本工种的安全技术操作规程。在操作中应监守工作岗位,未经领导许可,不准擅自将自己的工作交他人代管,不准做与工作无关的杂活。

4、注意劳逸结合,严禁酒后操作,严禁工作时间或工作面打闹、打瞌睡等不安全行为。

5、进入施工现场,作业人员应按规定必须佩戴安全帽,使用有规定的有关安全用品或用具,禁止穿拖鞋、高跟鞋、光脚及夏天女同志穿裙子。在没有防护设施的高空,悬臂或陡坡施工,必须系安全带,作业面距离地面2m 以上时,作业层面临边要有防护栏杆、挡板或安全网、钢板网作防护。安全帽、安全带、安全网等安全防护用品、用具要定期检查,对于检查不合格的严禁使用。

6、工作人员在高于2m 以上的高处作业时,所佩带的安全带必须将绳头挂在坚实的建筑物或结构坚实的的部位上,禁止穿硬底鞋,严格遵守高空作业纪律,睡眠不足或有精神病、高血压病者,均不得从事高空作业。

7、高空作业时,一切建筑物的脚手架、跳板和作业台面,必须事先检查,确保脚手架,建筑架和跳板等结构坚实后再作业。禁止在建筑架、跳板上站立、打闹、睡觉以及超过定额人数。

8、遇有恶劣天气如:风力在六级以上,影响施工安全时,禁止进行露天高空作业。

9、梯子不得有缺陷,不得垫高使用,梯子横挡间距以30cm 为宜,使用时上端要扎牢,下端要采取防范措施;平面梯与地面的夹角以60~70 度为宜;人字梯脚要拉牢,在通道处使用梯子,应有人专门监护或设置围栏。

10、如果没有安全防护设施,禁止在屋架上弦支撑杵条,悬挑梁和固定的构件上行走或作业,高空作业与地面联系,应设通讯设备,并专人负责。

11、乘人的外用电梯、吊笼,必须有可靠的安全装置及防坠落装置及超载自动报警装置,有防坠落实验报告,出厂合格证及检验报告和准用证,严禁工人在电梯顶乘坐电梯,严禁电梯超载运行,除指派的专业人员驾驶操作外,无关人员严禁驾驶外↕用电梯。

12、塔吊,除指派的专业人员驾驶操作外,严禁其他人员攀登及驾驶;禁止攀登起重臂、绳索及随同运料的吊篮,吊装物上下。

13、整体提升架,要有建设部的特批准用证明、相应的资质等级、施工方案、设计计算、安全等级证明、防坠落装置及方案、安全监管部门准用证。

高处作业频发,请收藏这份超全解决方案!

о

ē

北京工地高坠事故



 

安全意识是根本


安全体系是前提


责任落实是关键


管控措施是保障




ㄣ白小虎


安全投入是基础







美图、美文投稿请发送至邮箱:387234110@qq

关注我们


长按二维码

关注“平安市政”



[High fall accident] Suddenly! A worker in Beijing accidentally fell to his death while removing the scaffolding! Distressed: Chinese New Year is coming soon, please pay attention to safety! Click on Safe Municipal Administration above to subscribe! News from the official website of Beijing Emergency Management Bureau: At 16:00 on January 14, 2020, at the construction site of Cuihu Science and Technology Park on the east side of Huamei East Road, Haidian District, a worker from Beijing Jiayuan Jiayi Construction Engineering Co., Ltd. did not remove the scaffolding. Shen fell from a height and died after being rescued by the hospital. Please remember to dismantle the scaffold: from top to bottom, build first, then dismantle, and then dismantle first. Preparations for scaffold dismantling 1. According to the structure of the scaffold and the site conditions, the dismantling plan should be prepared and approved by the relevant authorities. u0026nbsp;2. Before the scaffold is dismantled, the safety area should be delineated and the cordon should be set up. The person in charge of the project convenes relevant personnel and operators to conduct a comprehensive field inspection of the scaffold, focusing on checking whether the fastener connection and fixing and supporting system meet the safety requirements. The personnel are familiar with the erection of the scaffolding on site. u0026nbsp;3. Confirm that the building and floor materials have been transferred, and the scaffolding can be removed only when it is confirmed that the scaffolding is not required. u0026nbsp;4. Before dismantling, check carefully and promptly remove the remaining materials or sundries such as floor ash, concrete blocks and so on on each shelf, and do not leave any materials and sundries with potential safety hazards. 5. When the frame body unloading wire ropes, scaffold rigid wall rods, and overhanging rods are removed, without the consent of the construction personnel and quality safety personnel of the project department, any operators on site shall not remove them at will, so as not to affect the quality and safety of the scaffolding. u0026nbsp;6. When scaffolding is dismantled, on-site operators must take protective measures and fasten safety belts. The dismantling is allowed after inspection and approval by the construction personnel of the project department, and the safety personnel will follow up and supervise the site. u0026nbsp;7. When the scaffolding is dismantled, according to the situation of the dismantlement site, the guard band set outside the site must be guarded by special personnel, and personnel irrelevant to this dismantling are prohibited from entering. u0026nbsp;8. Organize the demolition personnel to do a good job of safety technical confession, and have the signature of the recipient of the confession, and clearly understand the relevant safety technical requirements that should be paid attention to during the handover of the operator. And prepare safety belts, ropes, slings, tools, and transport personnel. u0026nbsp;9. Demolition personnel must be full-time scaffolding workers, and they can participate in the operation with a special type of work operation certificate. u0026nbsp;10. The security department of the project department will make a special security confession for the specific safety clarification. 2. The construction steps and key points of the external frame removal. The scaffolding should be removed according to the principle of top-down, first erect and then dismantled, and later dismantled first, and gradually dismantled. It is strictly forbidden to work up and down at the same time. Dismantle the discrete surface. All connecting wall poles should be removed layer by layer along with the scaffolding. It is strictly forbidden to remove the whole layer or several layers of connecting wall poles before removing the frame; while removing the connecting wall poles, temporary connecting wall poles should be installed for reinforcement. u0026nbsp;1. The construction process of scaffolding removal. The general sequence of scaffolding removal is: safety dense mesh → toe board → bamboo fence → scissor support (can only be dismantled on the dismantled layer) → diagonal brace (can only be dismantled on the dismantled layer) → Throwing support (can only be removed on the demolition layer) → small cross bar → large cross bar → upright rod → connecting wall rod. Among them, the cantilever channel steel and unloading wire rope of each cantilever scaffold are completely dismantled before the dismantling of the upper scaffold is completed. u0026nbsp;2. Precautions when removing the rodu0026nbsp;Workers must check their personal protective equipment before they can be put into use. Check whether the tools used are firm and prevent them from falling and hurting people. You must wear a safety helmet and a safety belt when working at heights or hanging in the air. u0026nbsp;① Upright pole—Hold the upright pole first and then loosen the butting fasteners, then pull out the upright pole steadily, and lay it flat on the next frame tube, then take out the fasteners, and do not leave it on the next upright pole. After the fastener is loosened, the pole is never allowed to be in an independent and free state, and it is not removed in time; the demolition personnel should not work alone, and two or more people should cooperate to remove it to ensure the safety of the removal. u0026nbsp;② Large crossbar, scissor brace, diagonal brace-first remove the middle butt fastener, hold the middle and then untie the end buckle; scissor brace and diagonal brace can only be removed on the demolition layer, not all at once, remove the scissors Safety belts must be fastened when supporting, and two or more people must cooperate to remove them. ③ Throwing—after the temporary support is used for reinforcement, the throwing is allowed to be removed. u0026nbsp;④ All connecting wall poles and unloading wire ropes are removed with the scaffolding layer by layer. It is strictly forbidden to remove the entire layer or several layers of connecting wall poles before dismantling the scaffolding. The height difference of sectioned removal is not more than 2 steps, if the height difference is more than 2 steps, temporary connecting wall rods are added for reinforcement. u0026nbsp;⑤ When the scaffold is removed to the height of the last long steel pipe at the bottom of about 6.0m, the temporary throwing or tie-up reinforcement should be set up at the appropriate location first, and then the connecting wall poles should be removed. u0026nbsp;⑥ The dismantled steel pipes should be passed from top to bottom and placed on the unremoved scaffolding on the lower level, but the number, height, and form of stacking should be transported to the ground by tower cranes or construction ladders according to safety standards. They should not be thrown at high altitude. Ensure safety, and pay attention to protecting the interior and exterior wall decoration surfaces and curtain walls to protect the finished product. ⑦ The loosened fasteners should be removed in time, placed indoors, not thrown at high altitude, packed using a tower crane, or transported to the ground along with the construction ladder. u0026nbsp;⑧ When removing to the safety flat baffle, it should be temporarily reinforced at an appropriate position before the diagonal brace can be removed. u0026nbsp;⑨During the process of dismantling, no substitutions are allowed. If a substitution is necessary, the dismantling situation should be clearly explained before leaving. Operators must check the scaffolds removed by themselves or their neighbors before leaving the site, and the loose racks must be dealt with before they can leave. u0026nbsp;⑩Fences or warning signs must be erected around the area. During the process of removing the scaffolding, there must be a special person to uniformly command, echo up and down, and coordinate movements. When untie the knot related to another, you should first notify the other party to prevent falling. ⑪The materials are transported by tower crane, and the dismantled materials are strictly prohibited to be thrown. The materials or components to be lifted must be bound firmly before they can be lifted. Do not injure others or damage buildings or public property during lifting. The materials transported to the ground should be dismantled and transported according to the designated location, stacked in categories, and cleaned on the same day as the dismantled materials. The dismantled fasteners should be collected and processed in a centralized manner. u0026nbsp;3. Safety measures for the removal of the outer frameu0026nbsp;①The personnel on duty for the removal of the outer frame must hold a special job-waiting certificate. Dismantling the scaffolding must be carefully confessed to the operator about safety technology. The team leader must clear the relevant safety technical requirements for the removal of the scaffold to the operators. ②The operator must wear a safety helmet, fasten a seat belt, wear non-slip shoes, and wear a tool bag when operating. The tool should be put into the bag after use and cannot be placed on a shelf to avoid falling and hurting people. u0026nbsp;③It is strictly forbidden to dismantle after drinking. The personnel who remove the scaffold must be in good health. Persons with a history of high blood pressure, fear of heights, etc. must not be put on the shelves. ④Removal of the outer frame should be carried out in the daytime, and regional maintenance should be done well. Warning signs should be hung up in obvious places of the passage and supervised by special personnel. During the entire demolition operation, the project safety officer should do a good job of on-site inspections, set up a guard area at the main passage, and arrange a guard to patrol to ensure the smooth progress of the demolition operation. u0026nbsp;⑤To remove the outer frame, first remove all the bamboo fences and safety nets, and then remove them from top to bottom. When removing, remove the horizontal rods first, and then remove the vertical rods. Do not work up and down at the same time. The connecting wall parts must be removed simultaneously with the scaffolding. Generally, it is not allowed to demolish in sections or on separate sides. If the separate sides must be demolished due to construction needs, side wall points and horizontal horizontal supports should be added at the two ends that will not be demolished temporarily. The removed fasteners and accessories should be transported to the ground in time, and it is strictly forbidden to throw them at high altitude. u0026nbsp;⑥All loose steel pipes and fasteners should be removed and transported away in time. ⑦The removed steel pipes are strictly prohibited to be thrown downstairs, and should be passed down layer by layer. u0026nbsp;⑧The dismantling should be carried out on all sides at the same time. It is forbidden to dismantle the other side after dismantling on one side. u0026nbsp;⑨Workers should pay attention to self-safety protection and the safety of others when working on the racks to avoid collisions, accidents and falling objects; it is strictly forbidden to play on the racks and sit on the railings and other unsafe places to rest. u0026nbsp;⑩During the operation, it is forbidden to dismantle the basic frame members, integral members, connecting fasteners and wall parts of the scaffold at will; when it is necessary to remove it, it must be approved by the chief technical engineer and take corresponding remedial measures. u0026nbsp;⑪All turnover materials under dismantling should be sorted and stacked neatly. Inspect one by one before putting it into the inventory, the deformed and damaged parts should be removed for repair, and those with paint peeling off should be repainted. u0026nbsp;Beijing construction site high fall accident⑫In case of severe weather such as strong winds and heavy rains, the operation should be stopped immediately, and the scaffolding should be protected. If necessary, the connection with the wall should be strengthened to ensure firmness. u0026nbsp;⑬In the process of dismantling the outer frame, the foremen and full-time security personnel of the project department inspected and monitored the whole process on the spot to ensure that no other personnel were working in the limited area of ​​the outer frame dismantling. 3. Safety technical operating rules for scaffolders (demolition part) 1. Demolition of scaffolding must be carried out in accordance with the special construction plan. Operators must be professionally trained, and be issued an operation certificate after passing the assessment, and take the job with the certificate. u0026nbsp;2. Safety belts must be used correctly when removing scaffolding. When the scaffolding is dismantled, it must be supervised by a special person, and fences or warning signs should be set up around it. Non-working personnel shall not be inside. Before dismantling the connecting wall point, check it first. After taking reinforcement measures, go from top to bottom in order and clear one step at a time. It is not allowed to cross-work up and down at the same time. u0026nbsp; u0026nbsp;3. To remove the scaffolding large crossbar and the scissor support, the middle buckle should be removed first, and then the two buckles should be removed, and the middle operator will move down the pole. u0026nbsp;4. Dismantled scaffold poles, scaffold boards, steel pipes, fasteners, steel wire ropes and other materials must not be thrown down. u0026nbsp;u0026nbsp;5. The dismantled outer scaffolding components must be sorted, stacked, and stacked neatly, and must not be disorderly. If it cannot be transported away in time, enough space should be reserved for stacking. The following animated picture is given to employees working at heights who did not want to wear seat belts. They fell and died. The scaffolding was unstable and gave their lives for nothing. The construction site collapsed. Fortunately, he was an agile guy who had no sense of safety and did not grasp his IQ. The last one of the revenge, the security measures are in place, even if it is clicked again, death has no chance! Here are some good practices for high-altitude rim work for praise Let’s take a look at how to set up safety belts when scaffolding is erected on the construction site. What if you don’t wear a seat belt in the picture below Ten prohibitions on climbing work 1 People who are contraindicated in climbing, such as workers with high blood pressure, heart disease, anemia, epilepsy, etc., are not allowed to climb. 2 Those who fail to go through the approval procedures for high-altitude operations in accordance with the regulations shall not climb. 3 Do not wear a safety helmet, safety belt, tight trousers, and do not ascend without supervision. 4 Do not ascend in the open air during heavy rain, heavy fog, and strong winds above level 6. 5. If the scaffolding and springboard are not strong, you cant climb high. 6 Ladder feet will not ascend without anti-skid measures. 7 Wear slippery shoes and carry bulky objects without climbing. 8 Asbestos tiles and glass fiber reinforced plastic tiles, without a firm springboard, it will not climb. 9 There is no block or ascend near the high-voltage line. 10 Insufficient lighting at night does not climb high Operators engaged in climbing operations must strengthen safety management in three aspects: establishing a climbing approval system, establishing a climbing equipment management system, and establishing a safe operation system for climbing workers. General system for fall prevention safety management 1. All high-altitude operators must receive high-altitude operations safety knowledge education; special high-altitude operations personnel should have a certificate to work, and special safety technology training should be carried out according to relevant regulations before work, and safety technology should be explained before operation Signing procedures. 2. Personnel working at heights should undergo a physical examination and be qualified before they can take up their posts. The project department shall provide qualified safety helmets, safety belts, safety nets and other safety labor protection supplies and related safety protection equipment for the operators. 3. Workers participating in the construction (including apprentices, interns, trainees and migrant workers) should be familiar with the safety and technical operating regulations of this type of work. During the operation, you should supervise your job position. Without the permission of the leader, you are not allowed to hand over your work to others, and you are not allowed to do miscellaneous tasks that are not related to the work. 4. Pay attention to the combination of work and rest. It is strictly forbidden to operate after drinking. It is strictly forbidden to engage in unsafe behaviors such as fussing and dozing off during working hours or at the working face. 5. When entering the construction site, operators must wear safety helmets and use relevant safety equipment or appliances as required. It is forbidden to wear slippers, high heels, bare feet, and summer skirts for lesbians. Safety belts must be worn in high-altitude, cantilevered or steep slope construction without protective facilities. When the working surface is more than 2m from the ground, protective railings, baffles or safety nets or expanded steel nets shall be provided on the side of the working layer for protection. Safety helmets, safety belts, safety nets and other safety protection products and appliances must be inspected regularly, and it is strictly forbidden to use them if they fail to pass the inspection. 6. When working at heights higher than 2m, the safety belts worn by the staff must be hung on a solid building or a solid structure. It is forbidden to wear hard-soled shoes and strictly abide by the discipline of working at heights. Those with insufficient sleep, mental illness, or hypertension are not allowed to work at heights. 7. During high-altitude operations, the scaffolding, springboards and work surfaces of all buildings must be checked in advance to ensure that the scaffolding, building frames and springboards are structurally solid before operation. It is forbidden to stand, fight, sleep, or exceed the quota on building frames or springboards. 8. In case of severe weather such as: the wind is above level 6, which affects the construction safety, it is forbidden to carry out open-air high-altitude operations. 9. Ladder must not have defects, and must not be used with height. The distance between the ladders cross blocks should be 30cm. When using, the upper end should be fastened, and the lower end should take precautions; the angle between the plane ladder and the ground should be 60~70 degrees; The foot of the ladder must be fastened firmly. When using the ladder in the passage, someone should be specially guarded or set up a fence. 10. If there is no safety protection facility, it is forbidden to walk or work on the roof truss to support the rods, cantilever beams and fixed components. For high-altitude operations and ground contact, communication equipment should be installed and a dedicated person should be responsible. 11. External elevators and cages for passengers must have reliable safety devices, fall prevention devices, automatic overload alarm devices, fall prevention test reports, factory certificates, inspection reports, and permits. Workers are strictly prohibited from riding on the top of the elevator. For elevators, it is strictly forbidden to overload the elevators. Except for the driving operations of designated professionals, unrelated personnel are strictly prohibited from driving external elevators. 12. For the tower crane, except for the designated professional driving operation, other personnel are strictly prohibited to climb and drive; it is forbidden to climb the boom, the rope and the hanging basket that accompanies the material, and lift the objects up and down. 13. The overall lifting frame must have a special approval certificate issued by the Ministry of Construction, the corresponding qualification level, construction plan, design calculation, safety level certificate, fall prevention device and plan, and safety supervision department approval certificate. Frequent high-altitude operations, please bookmark this super complete solution! High fall accident at Beijing construction siteu0026nbsp;Safety awareness is the fundamental safety system is the prerequisite, responsibility implementation is the key, control measures are to ensure the safety of Bai Xiaohu, investment is the basic beautiful pictures, American articles, please send to the email: 387234110@qqFollow us Long press the QR code to follow Safe Municipal Administration
广告位 ID:2 320*120

其他文章

登录

使用微信帐号直接登录,无需注册